Shaft Installation and Trimming Guide

These are recommendations for tip trimming 0.335" or 0.370" parallel tip shafts.

Printable Version

Pershing, YS+, YSQ, Quattro Tech, Throttle

Types	Products	Through- Bore	Blind-Bore	Std-Bore
Driver	Pershing 55, 65, 75 YS-5+, YS-6+, YS-7+ YSQ 55, 65, 75 Quattro Tech Md	0.0"	0.5"	1.0"
	Throttle	call	0.0"	0.0"-0.5"
	Pershing 45	Insert 2.0" only	Butt Trim Only
	Quattro Tech	Insert 2.0" only	0.0"	0.0"
#3 Wood	Pershing 55, 65, 75 YS-5+, YS-6+, YS-7+ YSQ 55, 65, 75 Quattro Tech Md	0.5"	1.0"	1.5"
	Throttle	0.0"-0.5"	0.5"	0.5"-1.0"
	Pershing 45	Insert 2.0" only	Butt Trim Only
	Quattro Tech	Insert 2.0" only	0.5"	0.5"
#5 Wood	Pershing 55, 65, 75 YS-5+, YS-6+, YS-7+ YSQ 55, 65, 75 Quattro Tech Md	1.0"	1.5"	2.0"
	Throttle	0.5"	0.5"-1.0"	1.0"
	Pershing 45	Insert 2.0" only	Butt Trim Only
	Quattro Tech	Insert 2.0" only	0.5"	1.0"

YS-6+ FW, YS-7+ FW, YSQ Fairway, YSQ75 Fairway

Types	Products	Through- Bore	Blind-Bore	Std-Bore
Fairway	3-wood	0.0"	0.5"	1.0"
	5-wood	1.0"	1.5"	2.0"

YS Hybrid+, YSQ Hybrid, TOUR AD UT - 55, 65, 85, 95 Hybrid

Types	Products	Standard Bore
Hybrid	YSQ Hybrid 85, YS Hybrid+ 85 (5.0", 0.370" parallel tip)	15°(deg)	19°	23°	27°	31+°
	YSQ Hybrid 85, YS Hybrid+ 85 (0.355" taper tip, 41.0", 41.5", 42.0")	0.0"	0.5"	1.0"	1.5"	2.0"
	Tour AD UT 55, 65 (2.5", 0.350" parallel tip, 44.0") Tour AD UT 85, 95 (2.5", 0.350" parallel tip, 42.0")	Butt trim only

G-TECH

WOOD	Driver	3W	4W	5W	7W
L or R Flex (5.0", 0.335" Parallel Tip)	0.0"	0.5"	1.0"	1.5"	1.5"
WOOD	Driver	3W	4W	5W	7W
A or S Flex (5.0", 0.335" Parallel Tip)	2.0"	2.5"	3.0"	3.5"	3.5"

IRON	3-IRON	4-IRON	5-IRON	6-IRON	7-IRON	8-IRON	9-IRON	PW
L or R Flex (6.0", 0.370" Parallel Tip)	0.0"	0.5"	1.0"	1.5"	2.0"	2.5"	3.0"	3.0"
IRON	3-IRON	4-IRON	5-IRON	6-IRON	7-IRON	8-IRON	9-IRON	PW
A or S Flex (6.0", 0.370" Parallel Tip)	1.5"	2.0"	2.5"	3.0"	3.5"	4.0"	4.5"	4.5"

Notes

• Graphite Design encourages consulting a PGA Professional or qualified clubmaker on selecting the best length shaft for your swing characteristics.
• Tip trimming is dependent on the bore depth and intended results.
• Tip trimming will increase frequency, tip stiffness and torque (amount of increase will vary depending on model.
• Always leave at least .5" of parallel tip section outside the hosel. For example: With a hosel depth of 1.5" and parallel tip length of 4", the trim should not exceed 2".
• Improper installation may affect the intended performance of the shaft.
• Warranty is for material and workmanship of products. Improper installation voids warranty of product.

Top